PVDF-based copolymers, terpolymers and their multi-component material systems for capacitor applications

Miniature of power electronics, scaling-down of microelectronics and other electrical and electronic systems, and development of many technologies (such as hybrid vehicles or implantable heart defibrillators) require capacitors with high energy density to improve the weight and volume efficiency of the whole system. Various capacitor technologies are investigated to meet the requirements of developing future technologies. Among these technologies, polymer film capacitor technology is one of the most promising. Besides high energy density, polymer-based capacitors possess the merits of high power density, low loss, high reliability (self-healing), easy processing, and feasibility (in size, shape and energy level).Due to the ferroelectricity of polyvinylidene fluoride (PVDF)-based polymers, they exhibit much higher polarization response under an electric field, in comparison with other linear dielectric polymers for capacitor applications. The maximum polarization level of PVDF-based polymers can be as high as 0.1 C/m2 and the breakdown field can be higher than 600 MV/m. An estimated energy density of around 30 J/cm3 can be expected in this class of materials. However, this value is much higher than the energy density that can be achieved in the PVDF homopolymer and the poly(vinylidene fluoride-trifluoroethylene) (P(VDF-TrFE)) copolymers due to the polarization hysteresis in these polymers. Therefore, in this thesis, PVDF-based polymer materials were investigated and developed to approach this expected energy density by various strategies. An energy density of higher than 24 J/cm 3, which is close to the predicted value, was found in PVDF-based copolymers.Recently, the poly(vinylidene fluoride-trifluoroethylene-chlorofluoroethylene) (P(VDF-TrFE-CFE)) terpolymer was developed in Prof. Qiming Zhang's group. Previous works have shown that incorporation of CTE into P(VDF-TrFE) copolymers, in which bulky CFE acts as a defect, could convert the copolymer into relaxor ferroelectrics. P(VDF-TrFE-CFE) terpolymers possess a high dielectric constant (larger than 50 at 1 kHz) at room temperature and excellent electromechanical properties.Here, the P(VDF-TrFE-CFE) terpolymers were studied as dielectric materials for capacitor applications. The electrical, thermal and microstructure characterizations were performed on the terpolymers. The terpolymers exhibit a high breakdown field (higher than 400 MV/m) and energy density (larger than 9 J/cm 3). The energy discharge characteristics of the terpolymer were studied by directly discharging the stored energy in the terpolymers to a load resistor. Due to the highly field-dependent nonlinear and frequency dependent dielectric response of the terpolymers, the discharge energy density and equivalent series resistance strongly depend on the load resistor and discharge speed. This study found that for high energy density dielectric materials, a very high dielectric constant might not be an advantage. In the case of terpolymers, this leads to early polarization saturation, i.e., polarization response saturates under an electric field much lower than the breakdown field and causes lower than expected energy density.Due to the dielectric nonlinearity and early saturation of polarization, the energy density of the terpolymers increases linearly with the applied electric fields. It was also found that the polymer-metal interface played an important role for conduction and the breakdown field in the terpolymers, which was related to the charge injection from the metal to the polymer. Due to highly nonlinear dielectric behavior and early polarization saturation in the terpolymers, it was proposed that a high dielectric constant might not be desirable to obtain high energy density. Poly(vinylidene fluoride-chlorotrifluoroethylene) (P(VDFCTFE), 10, 15 and 20 wt% CTFE) and Poly(vinylidene fluoride-hexafluoropropylene) (P(VDF-HFP), 10 and 12 wt% HFP) copolymers, which possess a much lower dielectric constant (about 12 at 1 kHz at room temperature), were further investigated for dielectric materials of high energy density. Due to the lower dielectric constant, the early polarization saturation was avoided and these polymers showed a very high breakdown field and energy density. For the P(VDF-CTFE) copolymer with 15 wt% CTFE, an energy density of higher than 24 J/cm 3 at an electric field higher than 650 MV/m could be obtained. Based on thermal and microstructure studies, the high energy density was found to be caused by the structural modification of PVDF by bulky CTFE or HFP, which also act as defects, similar to the terpolymers. The discharge behavior of the copolymers mainly relies on the load resistors, suggesting that the copolymers have lower equivalent series resistance.Multi-component material system based on current available materials was found to be a useful strategy to tailor and improve the performance of dielectric materials. Nanocomposites composed of the P(VDF-TrFE-CFE) terpolymers and ZrO2 or TiO2 nanoparticles were found to greatly enhance the polarization response and energy density of terpolymers (from 9 J/cm3 to 10.5 J/cm3). Based on comprehensive thermal, dielectric and microstructure studies, the enhancement was believed to be related to the large amount of interfaces in the nanocomposites. In the interfaces, the chain mobility is increased and the energy barrier between the polar and nonpolar phases is reduced, resulting in higher polarization response and energy density at a reduced electric field.The P(VDF-TrFE-CFE) terpolymer/P(VDF-CTFE) copolymer and the P(VDFTrFE-CFE) terpolymer/PMMA blends were also studied. It was found that the P(VDFTrFE-CFE) terpolymers could not be completely miscible with the P(VDF-CTFE) copolymer. In the P(VDF-TrFE-CFE) terpolymer/P(VDF-CTFE) copolymer blends, with a small amount of the copolymer (5 and 10 wt%) in the terpolymer, enhancement of the polarization response similar to that observed in the terpolymer/ZrO 2 nanocomposites was observed. This enhancement was also thought to be mainly caused by the interface effect. The breakdown field of blends was also greatly improved, which resulted in a significant improvement in energy density (from 9 J/cm3 to 11.5 J/cm3).The P(VDF-TrFE-CFE) terpolymers are miscible with PMMA. Addition of PMMA was found to reduce the dielectric response of blends, but also to improve the breakdown field due to the improvement of mechanical properties. The optimum composition of the blends is around 2.5 wt% PMMA. With this composition, the breakdown field of the blends can be improved without reduction of energy density.